Product Compare

Add two or more products and compare their details.

Name:
Image:
American Chiller CPPC Model Commercial Cold Plunge Chiller
Cup Anchor with Cross Bar
Deck Drain Corner Trench Channel, 90 Degree, Black
Deck Drain Tee Grating, Grey
Deck Drain Tee Trench Channel, White
KBE Lane Line Access Hatch
Neptune Benson Calibration Solution pH 4.65, 12ML
Neptune Benson Gold-Tip PPM Probe, Salt Water
Neptune Benson ORP Probe for Blu-Sentinel Pro/SE Controllers
Rubber Edging, 25M Rolls
Speck Normblock Series Swimming Pool Pump, Horizontal, Bronze, 1750 RPM
ZetaPool Fiamme Starting Block
ZetaPool Firenze Alto Starting Block
ZetaPool Genova Starting Block
ZetaPool Retractable Bayonette Peg
ZetaPool Starting Block
ZetaPool Udine Starting Block
ZetaPool Wall Anchor For Lane Lines, Non-Sloping
Teaser:
Description: American Chiller's CPPC Model Cold Plunge Pool Chillers are designed for serious cold tubs and pools. Engineered for every hot or cold ambient, any pool size and for heavy usage, for chlorine & salt water pools (specify when ordering).
 
Features 16 ga. Galvanized steel cabinet with high gloss powder coat finish EPA Compliant, R-407c refrigeration suitable for outdoors installation Copeland scroll compressor with crankcase heater and freeze stat safety thermosta Air cooled, high ambient, horizontal discharge condenser with head pressure control  Oversized receiver with outlet shutoff valve and pressure safety Single point power connection into weather proof electrical panel 24 vac control circuit with digital, electronic thermostat, compressor anti short-cycle timer, short-cycletime delay, water flow safety switch lockout, and high and low refrigeration pressure safety lockoutswitches. Titanium tube evaporator Liquid line specialties include externally equalized thermal expansion valve with liquid line solenoidvalve, filter drier, and sight glass Non ferrous water lines are wrapped in 1/2” closed cell insulation to minimize condensation System is factory leak checked, pressure tested, put under a deep vacuum, charged with refrigerant,and run tested under load prior to shipment Warranty: One (1) years limited parts, five (5) years limited compressor Options & Accessories: Condenser coil coating for corrosion protection in coastal areas Split system for outdoor condensing unit and indoor heat exchanger (for areas that have outdoor temperatures below freezing) Other voltages and options available; consult the factory
Engineered for durability and performance, our Lane Line and Wall Anchors are ideal for securing lane lines, buoy float lines, and pool toys in residential and commercial pools.
 
The KBE Lane Line Access Hatch was designed to provide a durable, space-saving solution for lane line storage in aquatic facilities. Built with both functionality and aesthetic appeal in mind, this lid and frame system seamlessly integrates into the pool deck. Its recessed design allows for easy tiling to match the surrounding surfaces, ensuring that the hatch remains unobtrusive and visually cohesive with your facility's design. This makes it an ideal choice for high-performance aquatic centers where both practicality and aesthetics are key.
 
Features: Dimensions: 14” x 14” Made of 316 Stainless Steel Resistant to corrosion, rust and harsh chemicals Durable Easy Operation Aesthetic Design Pop-Up Roller Mechanism Recessed Hatch Design
Keep your pool or spa water chemistry accurate and safe with pH 4.65 Calibration Solution. Designed for Blu-Sentinel and Strantrol pH probes, this solution ensures reliable calibration, allowing your water monitoring system to maintain proper pH levels for healthy, balanced pool and spa water.
 
Features: pH Value: 4.65 12 mL, perfect for single-use calibration in pool settings Works with Evoqua Blu-Sentinel and Strantrol pH probes used in pools and spas Maintains accurate pH readings, supporting proper sanitizer efficiency and safe swimming conditions Ideal For: Public and commercial pools Residential pools and spas Aquatic facilities requiring precise pH monitoring
Ensure accurate free chlorine monitoring in your saltwater pool with Neptune Benson's specialized gold-tip PPM probe, designed specifically for Blu-Sentinel controllers. Built to withstand the harsh conditions of saltwater systems, this probe delivers reliable PPM readings for precise water chemistry management.
 
Features: Gold-tip electrode for superior corrosion resistance in saltwater environments Measures free chlorine in PPM for accurate pool chemistry monitoring Designed for Blu-Sentinel controllers (check compatibility before installation) Durable, long-lasting construction for consistent performance Easy to install and calibrate Ideal For: Saltwater pools and spas Commercial and residential Blu-Sentinel systems Pool operators who require precise chlorine monitoring in PPM
Neptune Benson's ORP Probe provides accurate monitoring of Oxidation-Reduction Potential (ORP) in commercial pools, spas, and aquatic facilities. Compatible with Evoqua Blu-Sentinel SE and Blu-Sentinel Pro controllers, this probe ensures reliable sanitizer measurements for safe and properly balanced water.
 
Features: Delivers precise readings to monitor sanitizer activity effectively Blue probe allows for easy identification and maintenance Built to withstand the challenging conditions of commercial aquatic environments Probe sold without cable; compatible cables available separately Compatibility: Evoqua Blu-Sentinel SE and Pro controllers Applications: Commercial pools and spas Aquatic centers and water parks Systems requiring accurate ORP measurement for proper sanitizer control *If you have a Strantrol controller please confirm with a sales representative before ordering to confirm compatibility.
 
Designed for use with Evoqua's Blu-Sentinel Pro and Blu-Sentinel SE chemical controllers. This Neptune Benson Strainer comes with a ball valve and ensures that sample water flows over the strainer, preventing dirt particles from entering the flow cell module, thereby maintaining the accuracy and longevity of the sensors.
 
Features: Mesh Size: 0.5 mm, effectively filtering out dirt particles Ball Valve: Integrated for controlling water flow Specifically designed for the Blu-Sentinel Pro and Blu-Sentinel SE systems
This rubber edging is designed specifically for use between the pool’s movable floor and the pool walls. It creates a smooth, flexible barrier that prevents pinch points, protecting both the floor mechanism and users. Manufactured from durable, water-resistant rubber, this edging withstands repeated movement, chemical exposure, and daily use in aquatic environments. It ensures safe operation of the movable floor while extending the life of your pool’s components.
 
Features: Prevents pinch points between movable floor and pool structure Flexible, durable rubber construction Resistant to water, chemicals, and daily use Replacement part for KBE movable floors Sold in convenient 25 m rolls
At the highest end of the scale, Speck's bronze Normblock pumps push up to 3000 GPM. The Normblock Series has a robust horizontal single-stage design. This commercial pool pump is perfectly suited for aquatic facilities, waterparks, fountains, aquaculture and pools with elevated brine concentration.
 
Features: Available in 40, 50 & 60 HP Models. Superior slow (1750 rpm) running design reduces vibrations resulting in quiet operation Heavy duty energy efficient totally enclosed fan cooled (TEFC) motor, Class F insulation, protection class IP 55. Sealed ball bearings need no lubrication. Shaft coupling allows motor to be replaced without replacing the mechanical seal. A high wear, rugged Carbon/SiC - EPDM mechanical seal allows for long life and long maintenance intervals. SiC/SiC seals available upon request. Impellers are made of Bronze and individually balanced for optimum performance. Stainless steel shaft with 316 stainless steel protective shaft sleeve. The pump is ceramically coated. Optional all plastic strainer tank for horizontal flooded suction applications. *See downloads for part numbers and product data sheets.
The Fiamme Starting Block is built from 316 stainless steel. The structure is available with either a polished or an epoxy-painted finish. It features an adjustable, self-standing diving platform made from high-quality  plastic with a non-slip surface. The rear platform is also adjustable. A double stainless steel handle provides both horizontal and vertical grips for reliable backstroke starts. Numbers are displayed on all four sides of the block and are available in standard or customized versions. Designed in full compliance with FINA regulations.
 
Features: Block in stainless steel, metallic or painted with epoxy resins. Adjustable diving platform made of stainless steel AISI 316. Optional self-standing diving platform in plastic and non-slip surface. Double handle with horizontal and vertical grips. Numbers on all 4 sides (available with standard or customized numbers). Manufactured in accordance with FINA standards.
The Firenze Alto Starting Block is made from 316 stainless steel and is available in a polished or epoxy-painted finish. It features an adjustable, self-standing diving platform in plastic with a non-slip surface, ensuring secure starts for all athletes. The double stainless steel handle provides both horizontal and vertical grips for backstroke starts. A sloping base with an integrated step makes mounting easier. Numbers are displayed on all four sides of the block and are available in standard or customized versions. Designed in full compliance with FINA regulations.
 
Features: Stainless steel, metallic or painted with epoxy resins. Sloping base with step for mounting. Adjustable diving platform made of stainless steel AISI 316. Optional self-standing diving platform in plastic with non-slip surface. Double handle with horizontal and vertical grips. Numbers on all 4 sides (available with standard or customized numbers). Manufactured in accordance with FINA standards.
The Genova Starting Block features a durable PVC structure with an adjustable, self-standing diving platform made from high-quality plastic and a non-slip surface. The rear platform is adjustable and the double stainless steel handle provides both horizontal and vertical grips for secure backstroke starts. Numbers are displayed on all four sides of the block and are available in standard or customized versions. Designed in full compliance with FINA regulations.
 
Features: PVC structure. Adjustable diving platform made of plastic with non-slip surface. Adjustable rear platform Double handle with horizontal and vertical grips. Numbers on all 4 sides (available with standard or customized numbers). Manufactured in accordance with FINA standards.
The retractable bayonette peg is used for fixing racing lanes to the poolside. Constructed from 316 stainless steel, it is available in diameters of 45 mm or 48 mm.
 
Features: Constructed from 316 stainless steel. Available in diameters of 45 mm or 48 mm.
The Zeta Starting Block is made from 316 stainless steel and is available in a polished or epoxy-painted finish. The self-standing, adjustable diving platform is built from non-slip, high-density polyethylene, measuring 500 by 700 millimetres, with an adjustable rear platform to accommodate various athlete preferences. The double stainless steel handle offers horizontal and vertical grips for backstroke starts. Numbers are displayed on all four sides of the block and are available in standard or customized versions. Designed in full compliance with FINA regulations.
 
Features: Stainless steel, metallic or painted with epoxy resins. Adjustable diving platform made of AISI 316 stainless steel. Optional self-standing diving platform made from plastic with a non-slip surface available. Includes an adjustable rear footrest. Double handle with horizontal and vertical grips. Numbers on all 4 sides (available with standard or customized numbers). Manufactured in accordance with FINA standards.
The Udine Starting Block features a PVC barrel and a high-density polyethylene platform with non-slip surface. The rear foot platform is adjustable to multiple positions, providing flexibility for athletes. The double stainless steel handle offers both horizontal and vertical grips for reliable backstroke starts. Thanks to its plastic copolymer and PVC construction, the Udine Starting Block is unaffected by corrosion from chemicals in the water, making it a low-maintenance choice that offers excellent stability. Numbers are displayed on all four sides of the block and are available in standard or customized versions. Designed in full compliance with FINA regulations.
 
Features: Made of plastic copolymer Sturdy, corrosion-resistant PVC barrel Platform made of high density polyethylene with non-slip surface.  Includes adjustable rear footrest. Double handle with horizontal and vertical grips. Numbers on all 4 sides (available with standard or customized numbers). Manufactured in accordance with FINA standards.
Wall anchoring for lane in stainless steel 316.
Rating:
Material: n/a n/a n/a n/a n/a n/a n/a Stainless steel n/a n/a n/a n/a Rubber n/a Stainless steel, metallic or painted with epoxy resins Stainless steel, metallic or painted with epoxy resins PVC with Stainless Steel Handles Stainless steel Stainless steel, metallic or painted with epoxy resins. Plastic copolymer, PVC, stainless steel n/a
Measurements: n/a n/a n/a n/a n/a n/a n/a 14” x 14” n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a 500 by 700 millimeters n/a n/a
Size: n/a n/a n/a n/a n/a n/a n/a n/a 12mL n/a n/a n/a 25M Roll n/a n/a n/a n/a n/a n/a n/a n/a